Facility Executive Technical

JLL empowers you to shape a brighter way .

Our people at JLL are shaping the future of real estate for a better world by combining world class services, advisory and technology for our clients. We are committed to hiring the best, most talented people and empowering them to thrive, grow meaningful careers and to find a place where they belong. Whether you’ve got deep experience in commercial real estate, skilled trades or technology, or you’re looking to apply your relevant experience to a new industry, join our team as we help shape a brighter way forward.

Facility Engineer with below requirement.

A. Power Quality, Distribution & Reliability

• Operate and maintain LT systems, transformers, LT panels, PDU/RPP, isolation transformers , and static transfer switches (STS) .

• Ensure N+1 / 2N redundancy for critical loads (process tools, scrubbers, abatement, BMS, safety systems).

• Monitor harmonics (THD), transients, flicker , and EMI/RFI ; implement filters/SPDs and isolation strategies for sensitive tools (litho, metrology).

• Perform load studies , phase balancing, and feeder capacity checks prior to tool hookups and expansions.

B. UPS, Emergency Power & Controls

• Operate and maintain UPS (modular/N+1), battery strings, DG sets , AMF/ATS panels; test black start and autotransfer sequences.

• Periodic battery health tests (IR, discharge tests), UPS efficiency tuning, and firmware/config backup.

• Maintain Emergency Power Off (EPO) circuits, interlocks with gas monitoring systems , and fire alarm interfaces .

C. Grounding, Bonding & ESD

• Maintain clean/technical grounds , separate from building ground; verify low-impedance paths and equipotential bonding for tools.

• Implement and audit ESD controls (SEMI S20.20 practices), wrist straps, surfaces, flooring resistance, and static-safe layouts in cleanroom and chase areas.

D. Maintenance, Monitoring & Response

• Establish PM/CBM for panels, breakers, relays, STS, UPS, and IR thermography for hot spots.

• Trend MTBF/MTTR , create SPC charts for voltage, frequency, THD, and temperature rise.

• Lead RCA on trips/nuisance faults; implement corrective and preventive actions.

E. Safety & Compliance (Electrical)

• Enforce LOTO , arc-flash boundaries, insulated tools, and PPE.

• Maintain single-line diagrams , relay settings, test reports (IR, ER), and statutory compliance under CEA Regulations , Indian Electrical Safety Rules , and local inspectorate requirements.

• Integrate BMS/EPMS alarms, define SOPs for emergency shutdowns and controlled restarts.
• Facility Engineer – Mechanical / Process Utilities (Semiconductor Labs)

Primary Objective

Ensure stable, spec-compliant utilities for process tools and cleanroom performance with high uptime and contamination control.

A. Cleanroom & HVAC (Critical Environment)

• Operate and optimize MAUs/AHUs/FFUs , HEPA/ULPA filtration, pressurization cascades , temperature & RH controls.

• Maintain ISO 14644 cleanroom classes; track particle counts , airflow, and room recovery times .

• Handle filter life-cycle management , leak tests (DOP/PAO), duct hygiene , and IAQ .

• Seasonal tuning of coils, economizer modes , and dew point management to prevent condensation in bays/chasers.

B. Chilled Water / PCW /

• Operate chillers (centrifugal/screw), CTs, primary/secondary pumping , and PCW loops for tools.

• Maintain temperature stability , ΔT, flow, and vibration on critical pumps; maintain N+1 for critical circuits.

• Water treatment: scaling/corrosion inhibitors, biocide control, blowdown optimization.

• Trending: SPC on supply temp , differential pressure, specific energy consumption .

C. Ultra-Pure Water (UPW/DI) & Wastewater

• Manage rinse loops , sanitization schedules, and return/reclaim strategies (if applicable).

D. Compressed Air (CDA), Vacuum & Inert Gases

• Operate oil-free compressors , dryers, and filtration to meet dew point and oil/particulate specs; maintain VMB/VMP pressures.

• Maintain central vacuum and dry pump systems for tools; plan overhauls , flushing , and pump swap programs with OEMs

• Manage bulk/packaged nitrogen (N₂) , vacuum-jacketed lines (if LN₂), and purges for tools and abatement.

E. Fire, Life Safety & Exhaust/Ventilation

• Maintain process exhaust , toxic exhaust , and general exhaust with redundancy and failure interlocks.

• Coordinate with fire detection/suppression (VESDA, clean agent where applicable), and ensure SEMI S2/S6/S8/S18 oriented risk controls.

F. Maintenance, Monitoring & Analytics PPM

• Create PM schedules for pumps, compressors, chillers, FFUs, filters, cabinets, scrubbers, UPW, and neutralization systems.

• Use BMS to alarm, trend, and report; deploy predictive maintenance (vibration, oil analysis, dew point trends).

• Maintain spares strategy for high-risk items (VFDs, AHU motors, pump seals, pH probes, sensors, HEPA/ULPA, MERV prefilters).

H. Safety & Compliance (Mechanical/Utilities)

• Enforce PTW/LOTO , confined space, hot work, and chemical handling SOPs.

• Comply with Factory Act , Boiler Regulations (if applicable), Lift Act , local PCB norms for discharge, PESO/SMPV Rules for gas storage, and explosion-proof ratings where needed.

• Maintain MSDS/SDS , calibration certificates, and interlock validation records.
• Common Responsibilities (Both Electrical & Mechanical)

Projects & Tool Hookups

• Review PFD/P&ID , MEP/shop drawings , and hook-up packages ; validate utility points, capacity, and interlocks.

• Coordinate FAT/SAT , commissioning, and as-built updates; manage change control and redlining.

• Plan shutdowns with clear MOPs (Method of Procedure) and rollback plans—particularly when tying into live loops.

Operations, Documentation & Reporting

• Maintain O&M logs , trend charts , equipment history , and SOP/EOP libraries.

• Generate MIS : uptime, incidents, energy use, water use, chemical use, and environmental KPIs (e.g., CUE/WUE).

• Track OEE , MTBF/MTTR , and SPC metrics for